Skip to content

How to Fog an Outboard Motor

Table Of Contents
 Maintenance Guide · Winterization

How to Fog an Outboard Motor

The complete step-by-step guide to fogging your outboard for winter storage — why it matters, exactly how to do it in 5 steps, and how to avoid the mistakes that ruin motors every year.

 ~20–30 minutes  Skill level: Beginner  For 2-stroke & 4-stroke outboards  Fits all major brands
Start the 5-step guide

Fogging is the single most important thing you can do before storing an outboard for winter — or for any period longer than a few weeks. Miss this one step, and moisture left inside the engine can rust cylinder walls, piston rings, bearings and crankshaft surfaces: damage that is expensive to repair and usually only discovered next spring. This guide explains what fogging is, why it works, and how to do it correctly, step by step, on both two-stroke and four-stroke outboards.

Why it matters

Why You Should Fog Your Outboard Before Storage

When an outboard sits idle for months, the engine cools down overnight and moisture condenses inside the combustion chambers, crankcase and bearings. Trapped moisture plus air equals rust — and rusted cylinder walls and bearings are among the most common causes of “seized” or hard-starting outboards after winter.

Rusted outboard engine cylinder wall and piston caused by lack of fogging oil What neglect looks like: rust & pitting on an unprotected cylinder

Rust needs only two things — moisture and oxygen. A stored engine has both.

Every time the engine cools, humid air is drawn in and condensation forms on bare metal. Over a whole winter, that’s enough to pit cylinder walls, scar piston rings and seize bearings. The result is an engine that won’t start in spring — or one that needs costly machine work.

Fogging solves this with a simple, cheap insurance policy: a thin film of special oil that seals every internal metal surface against air and moisture for months.

20minOf work protects your engine all winter
1 winterOf neglect is enough to pit cylinder walls
100%Of internal surfaces need that oil film
The principle

How Fogging Works

Fogging oil is sprayed into the air intake while the engine is running. The engine’s own suction draws the fine oil mist through the intake, into the combustion chamber and over every moving part — leaving a thick, sticky protective film that blocks rust.

1 · Spray into the intake

Fine oil mist is sprayed into the air intake while the engine idles.

2 · Mist coats the engine

Suction carries the mist over pistons, rings, valves, bearings and cylinder walls.

3 · Protective film remains

A thick oil layer seals metal from air and moisture until next season.

Get ready

What You’ll Need

Everything below is inexpensive and available at any marine store or online. Gather it before you start so the job goes smoothly.

Marine fogging oil

Aerosol can — e.g. Yamalube, Mercury or Quicksilver Fogging Oil.

Cooling water source

A large tub or barrel of water, OR flush muffs (earmuffs) with a garden hose.

Fuel stabilizer

Treat the fuel so it doesn’t gum up while the engine is stored.

Spark plug socket & ratchet

Only needed if you do the recommended spark-plug-hole fogging (Step 5).

Screwdriver / socket set

To remove the air filter box or intake silencer cover.

Gloves & safety glasses

Fogging oil is sprayed as a fine mist — keep it off skin and out of eyes.

Step by step

How to Fog an Outboard Motor: 5 Steps

Follow these steps in order. If you have an owner’s manual, keep it nearby — model-specific details always win.

  1. 1

    Connect Cooling Water Never run dry

    Mount the lower unit in a large tub or barrel of water, or attach flush muffs (earmuffs) over the water intake screens and open the garden tap. You must have cooling water circulating before the engine ever starts.

    • A tub of water works best for a full flush of the cooling passages.
    • With muffs, make sure they fully cover both intake screens and the water is flowing.
    • Raise the cowl / remove the engine cover so the intake is easy to reach for Step 3.
    Never start the engine without water. Even 10 seconds of running dry can burn out the water pump impeller instantly — it relies on water for both cooling and lubrication.
    Outboard motor winterizing with lower unit submerged in a water tub
  2. 2

    Start the Engine & Warm It Up Use stabilized fuel

    If the engine will be stored with fuel in it, mix in a fuel stabilizer now. Start the engine and let it idle for 5–10 minutes until it reaches normal operating temperature.

    • A warm engine helps the fogging oil spread evenly and cling to hot metal surfaces.
    • Confirm the tell-tale (pee hole) is spitting water — proof the cooling system is working.
    • Give the engine a few quick revs to warm it thoroughly before fogging.
    Don’t fog a cold engine. On a cold engine the oil can settle unevenly and leave unprotected spots. Warming up first is what lets the thermostat open and the film reach every surface.
  3. 3

    Spray Fogging Oil into the Air Intake The core step

    Remove the air filter box / intake silencer cover to expose the carburetor(s) or EFI throttle body. With the engine still idling, spray the fogging oil directly into each carburetor intake, one after another, in short bursts.

    • Keep spraying until thick white/blue smoke pours from the exhaust — that’s the oil coating the internals, and it’s completely normal.
    • Expect the engine RPM to drop slightly as the oil-rich mixture chokes it — that’s a sign it’s working.
    • Multi-carb two-strokes: don’t stop after the first carb — hit every one.
    For EFI / direct-injection models: follow your owner’s manual. Many specify spraying through the throttle body or via the fuel system, and some high-end models (e.g. certain Mercury or Evinrude E-TEC) have an automatic fogging program. Read the manual before spraying to avoid damaging sensitive sensors.
    Spraying marine fogging oil into the outboard motor air intake
  4. 4

    Stall It Out to Lock the Oil Film Seal it in

    Keep feeding fogging oil into the intake while increasing the spray until the engine coughs and stalls from the oil — or simply turn the key off. Either way, the engine is now evenly coated inside with a protective film.

    • Stalling it out on oil is the surest sign the whole induction path got coated.
    • After it stops, pull the starter rope or turn the flywheel a few times to help distribute the film.
    • Disconnect the battery or keep the kill switch off so the engine can’t accidentally fire up.
    Goal: a thick film, not a dry engine. If the engine won’t stall, keep spraying a little more until it does. Better too much oil than not enough.
  5. 5

    Fog Through the Spark Plug Holes Optional but recommended

    For maximum protection, disconnect the plug wires, remove all spark plugs, and spray a short burst (~2–3 seconds) of fogging oil into each cylinder through the spark plug hole.

    • Manually turn the flywheel / pull the starter a few times to spread the oil evenly over the cylinder walls.
    • Reinstall the plugs finger-tight, then a quarter-turn with the socket — don’t over-tighten.
    • Leave the plug wires off until you’re ready to start the engine next season.
    Why do it? This is double insurance. It guarantees oil reaches the upper cylinder area even if the intake spray missed a spot — especially valuable on four-stroke outboards.
    Removing spark plugs to fog an outboard motor cylinder
Know your engine

Two-Stroke vs Four-Stroke: What’s Different

Both engine types need fogging, but the details differ. Here’s how to handle each.

AspectTwo-StrokeFour-Stroke
Need for fogging Critical — crankcase & bearings are exposed to the fuel/air mix, so unprotected bearings rust fast. Important — cylinder, valves & upper end still need the protective film.
Where to spray Directly into every carburetor intake (all carbs on multi-cylinder engines). Into the throttle body / intake per the manual; some models need a special procedure.
Auto-fogging Rare — fogging is almost always done manually. Some EFI models (Mercury, Evinrude E-TEC) have automatic fogging programs — check the manual.
Crankcase protection Oil is mixed with fuel, so the mist coats the crankcase naturally — this is why fogging is so effective here. Separate oil system; fogging protects the top end and combustion chamber.
Extra tip Never skip a carb — an un-fogged carb’s cylinder is a rust risk. Never spray onto electronic sensors or the throttle position sensor.
Spring is coming

First Start Next Season — Expect Smoke

Thick smoke at first start is normal — don’t panic. When you first start a fogged outboard next season, the protective oil film burns off and the engine will blow thick smoke for a few minutes. This is completely normal: the smoke clears as the oil burns away, and the engine settles back to normal running within a few minutes. Make sure you start it with cooling water connected, just like you did for fogging.
Do it right

Common Mistakes & Pro Tips

Never run the engine dry

No cooling water = dead impeller in seconds. Water is its only lubrication.

Warm the engine first

Fogging a cold engine leaves uneven, patchy oil coverage.

Use dedicated fogging oil

Use marine fogging oil (Yamalube, Mercury, Quicksilver) — not WD-40 or plain engine oil.

Don’t skip any carb

On multi-cylinder two-strokes, every carb intake needs its own dose.

Stabilize the fuel & fill the tank

Stabilized, full tanks prevent condensation and fuel gumming over winter.

Service before you store

Change gearcase oil, check the anode, and clean the propeller while you’re at it.

Questions

Frequently Asked Questions

How long does fogging take?
Around 20–30 minutes once you have everything ready — the bulk of that is the 5–10 minute warm-up in Step 2.
Is fogging the same as winterizing?
Fogging is one key part of winterizing. A full winterization also includes fuel stabilization, changing the gearcase oil, checking the battery, flushing the cooling system and storing the motor properly. Fogging is the step that protects the engine internals.
Can I fog a fuel-injected (EFI) outboard?
Yes. EFI outboards need fogging too, but follow the manual: spray through the throttle body as specified, and never spray onto electronic sensors. Some EFI models have an automatic fogging program you can run instead.
Do I have to remove the spark plugs every time?
No. On carbureted models, spraying through the intake (Step 3) covers most of the engine. Removing the plugs for the extra fogging (Step 5) is optional double insurance — well worth it on four-strokes.
What if my outboard was stored without fogging?
First, try turning the flywheel by hand with the plugs out. If it turns freely, fog it now before running it. If it’s seized or very hard to turn, don’t force it — have a marine mechanic assess the damage.

Keep Your Outboard Running Season After Season

Fogging oil, genuine maintenance parts and reliable outboard motors — Yamabisi has the gear to keep you on the water. Explore the range and find the right motor for your boat.

Questions about a specific model? Contact our team for model-specific winterization advice.

Share With

Latest Articles

Ink & Toner Finder

Brand
Series
Model
Get Quote