Let’s be real for a second. Putting your boat away for the winter feels like saying goodbye to a good friend. The days get shorter, the water gets colder, and the cover goes on. But here is the thing: how you say goodbye determines how sweet the reunion will be next spring.
You are probably Googling “what do you need to winterize an outboard motor” because you care about your machine. You should. An outboard isn’t just an engine; it’s your ticket to freedom on the water. Ignoring winter prep is like parking a car in the ocean and hoping it starts in six months. It won’t.
At Yamabisi, we build our outboards to withstand punishment. We use marine-grade aluminum and advanced anti-corrosion coatings. But even a tank needs maintenance. Winterization isn’t a chore; it’s an insurance policy. A few hours now guarantees your Yamabisi wakes up purring next season, keeping that legendary reliability intact for a decade or more.
Ready to get your hands a little dirty? Here is your definitive, no-nonsense guide.

1. Fuel System: Don’t Let Gas Turn Into Gunk
If you take one thing away from this guide, let it be this: Old gas is the enemy.
Modern fuel contains ethanol. Over time, ethanol attracts moisture from the air. When that water separates from the gas, it sinks to the bottom of your tank and wreaks havoc on your carburetor or fuel injectors. If you leave untreated gas in your system all winter, you are essentially asking for a gummed-up engine that won’t start in April.
The Fix: You need a high-quality marine fuel stabilizer. Don’t skip this. Pour the stabilizer into your fuel tank (follow the bottle’s ratio), and then—this is the crucial part—run the engine. Hook it up to a flush muff or a water tank and let it idle for about 10-15 minutes. This ensures the treated fuel works its way through the entire system, from the tank to the injectors. You want that protective chemical barrier everywhere.
2. The Internal Armor: Fogging the Engine
Cold storage creates condensation. Condensation leads to rust. Rust inside your cylinders? That is the kiss of death for an outboard.
You need to protect the internal heart of your machine—the cylinder walls and pistons. This is where fogging oil comes into play. Think of fogging oil as a heavy, sticky blanket that clings to the metal inside your engine, shielding it from moisture while it sleeps.
How to do it:
- For 2-Stroke Yamabisi Models: With the engine running (and fuel stabilized), spray the fogging oil directly into the carburetor intake until the engine starts to smoke heavily and eventually stalls. That smoke means the oil has coated everything.
- For 4-Stroke Yamabisi Models: It’s a bit more precise. Remove the spark plugs and spray the fogging oil directly into each cylinder. Turn the flywheel by hand a few times to spread the oil evenly.
Pro Tip: While you are there, check your spark plugs. If they look fouled, toss them. Install fresh Yamabisi Genuine Spark Plugs in the spring, but leave the old ones in for storage to seal the holes.
3. The Lower Unit: Playing Detective with Gear Oil
The lower unit is where the magic happens—it transfers all that horsepower to the prop. It’s also the part of the motor that spends its life underwater.
Winterizing is the perfect time to check the health of your seals. You need to drain the gear oil. Place a pan underneath and open the drain screw.
Watch the color closely:
- Amber/Dark Brown: Good news. Your seals are tight.
- Milky/Coffee-colored: Bad news. Water has gotten in.
If the oil is milky, water is mixing with the lube. If you leave that water in there over winter and it freezes, it expands. That expansion can crack your lower unit casing. That is an expensive fix you don’t want.
If you see water, you likely need new prop shaft seals or drain gaskets. Replace them immediately with Yamabisi OEM parts. Once drained, pump in fresh, high-viscosity Marine Gear Lube from the bottom hole until it flows out the top vent. Do not use automotive oil; it can’t handle the marine load.
4. Corrosion Control: The Sacrificial Lambs
Saltwater and moisture never sleep. They are constantly trying to eat away at your motor’s metal.
Your Yamabisi outboard comes equipped with sacrificial anodes. These are those little unpainted metal blocks you see on the lower unit and bracket. They are made of zinc or aluminum, and their sole job is to corrode so your engine doesn’t have to. They take the bullet for the team.
The Inspection: Look at them. Are they pitted? Crumbling? If they are more than 50% dissolved, swap them out. Do not wait. Installing a fresh set of anodes is the cheapest way to protect the integrity of your outboard’s body.
Also, give the exterior a good wash. Use soap and water to remove salt buildup, and consider applying a silicone spray or a specialized anti-corrosion guard to the powerhead (avoiding electrical contacts).
5. Grease Points: Keep the Joints Moving
A stiff engine is an unhappy engine. Your outboard has several pivot points that need to move freely—the steering tube, the tilt/trim mechanism, and the throttle linkages.
Grab a grease gun loaded with marine-grade grease (waterproof is key here). Hit every Zerk fitting (grease nipple) you can find until you see fresh grease oozing out. This pushes out any trapped water and ensures that when you go to steer the boat next spring, it doesn’t feel like you’re wrestling a bear.
Don’t forget the Prop Shaft: Pull the propeller off. Seriously, take it off. Fishing line loves to wrap around the shaft behind the prop, cutting into seals silently. Check for debris, clean the shaft, and slather it in fresh grease before sliding the prop back on.
6. Storage Position: Let Gravity Help
How you store the motor matters. You should store the outboard in a vertical (down) position.
Why? Gravity. You want to ensure every drop of cooling water drains out of the engine block. If you store it tilted up, water can get trapped in the cooling passages. If that water freezes, it expands and cracks the block. Storing it vertically also prevents oil from pooling in the wrong parts of the cylinders on 4-stroke models.
If you are taking the battery out (which you should), store it on a wooden block or shelf in a cool, dry place. Hook it up to a trickle charger. A dead battery left in the cold often becomes a useless battery by March.
7. The Forward Look: Is It Time for an Upgrade?
You’ve gone through the checklist. You’ve flushed, fogged, greased, and drained. Your current motor is safe.
But as you pack up, ask yourself: Did this motor do everything I wanted it to do this year?
Winter is the quiet season, but it’s the smartest time to upgrade. Maybe you need more torque for that new tow tube. Maybe you want the fuel efficiency of a modern 4-stroke. If your current rig is aging, or if you just want that new-engine peace of mind, check out the latest Yamabisi lineup. From portable 2.5HP kickers to our robust 40HP workhorses, winter is the perfect time to refit your boat so you are ready to rip the moment the ice melts.
FAQ: Common Winterizing Questions
Q: Can I use car antifreeze in my outboard? A: Generally, no. Most outboards use raw water cooling (lake/ocean water). You don’t fill them with antifreeze like a car radiator. The goal is to drain the water out. However, for inboard/outboard systems or specific storage conditions, running non-toxic marine antifreeze (the pink stuff) through the system can flush out pockets of water. Always check your Yamabisi owner’s manual first.
Q: Do I really need to change the gear oil if I only used it a few times? A: Yes. It’s not just about wear; it’s about water. Even a few trips can compromise a seal. If water sits in that gear case all winter, you are looking at rusted gears or a cracked housing. It’s a cheap fluid change that saves thousands in repairs.
Q: Can I just start the engine dry for a few seconds to blow the water out? A: Absolutely not. The water pump impeller needs water for lubrication. Running it dry, even for 5 seconds, can melt the impeller rubber. Once that’s damaged, your engine will overheat next time you use it. Always use muffs or a tank.
The Bottom Line
Winterizing isn’t rocket science, but it is precise. It requires the right fluids, the right parts, and a little bit of patience.
By following these 7 Essential Steps, you aren’t just storing a motor; you are guaranteeing that your Yamabisi remains the reliable, durable beast you bought it to be.
Need the right stuff to get the job done? Don’t guess with generic parts. Check out our Genuine Yamabisi Maintenance Parts and get your rig ready for a long winter nap. Trust us, your future self (and your boat) will thank you.


