Skip to content

Winterizing Your Outboard Motor: Protect Your Investment

Table Of Contents

When the boating season comes to a close, properly preparing your outboard motor for off-season or long-term storage (two months or longer) is the most critical maintenance task you can perform.

Neglecting this process leaves your engine vulnerable to its three biggest enemies: rust, corrosion, and freeze damage from trapped water. A little preparation now ensures your Yamabisi outboard—or any marine engine—will fire up effortlessly when spring arrives.

Here is our comprehensive, step-by-step guide to winterizing your outboard motor safely and effectively.

Warning: Never run your outboard dry. Operating the engine without a sufficient supply of cooling water will instantly destroy the water pump impeller and cause severe engine overheating. Always use a flushing attachment (earmuffs) or a test tank.

Waterproof 48v Dc Electric Outboard Trolling Motor

1. Stabilize the Fuel System (The Ethanol Threat)

Modern gasoline, particularly ethanol-blended fuel (E10 or higher), is notorious for attracting moisture. If left untreated during winter, this water can freeze or cause “phase separation,” creating a corrosive sludge that will gum up your carburetors or fuel injectors.

For Portable Fuel Tanks: Add a high-quality marine fuel stabilizer to the tank at the recommended ratio. Agitate the tank gently to ensure the stabilizer mixes thoroughly with the gasoline.

For Built-in / Permanent Fuel Tanks: Add the appropriate amount of marine-grade fuel stabilizer directly into the tank.

Treating the Engine:

  1. Remove the fuel filter’s water-separating bowl. Safely dispose of the existing liquid.
  2. Add about 3ml (1/2 teaspoon) of concentrated fuel stabilizer directly into the bowl, then securely reinstall it.
  3. Supply cooling water to the engine (via earmuffs or a tank) and run the motor at a fast idle for 10 to 15 minutes. This ensures the stabilized, treated fuel circulates completely through the fuel lines, pumps, and entire engine system, preventing varnish buildup.

(Note: If you use alcohol-heavy fuels, some mechanics recommend completely draining the tank and lines. However, a properly stabilized closed fuel system is generally safe for standard winter storage without draining.)

2. Fog the Engine: Protecting Internal Components

While your engine sits idle, the thin film of oil inside the cylinders can drain away, leaving bare metal exposed to condensation and rust. “Fogging” the engine coats these critical internal parts with a protective layer of thick anti-corrosive oil.

  1. Turn off the engine and carefully remove all spark plugs.
  2. Spray approximately 1 oz (30 ml) of marine storage fogging oil directly into each spark plug hole.
  3. Briefly crank the engine over for one starting cycle (without starting it). This motion distributes the fogging oil evenly across the cylinder walls and piston rings.
  4. Clean, inspect, and reinstall the spark plugs (or replace them if they are fouled).

3. Change the Lower Unit Gear Lube

Never store your outboard without changing the gear oil in the lower unit. During the season, fishing lines can damage propeller seals, allowing tiny amounts of water into the gearcase. If left inside during freezing temperatures, this water will expand and crack the expensive lower unit housing.

Drain the old gear lube completely. Inspect it closely: if the old oil looks “milky” or creamy, water has intruded, and your seals must be replaced by a professional. If the oil is dark but clear, simply refill it from the bottom drain hole up to the vent hole using premium marine gear lube.

4. Protect the Exterior and Moving Parts

Your engine’s exterior battles harsh UV rays and corrosive environments all season long. Give it a final layer of defense:

  • Touch up any chipped paint on the cowling or midsection to prevent bare metal oxidation.
  • Apply a heavy-duty marine anti-corrosion spray (avoiding the sacrificial anodes, as they need to remain exposed to work properly) to the external metal surfaces and electrical connections under the cowl.
  • Use a grease gun to pump fresh marine grease into all zerk fittings, steering tubes, and pivot points.

5. The Golden Rule: Store It Vertically

How you physically position your outboard motor during storage is crucial. Always store your outboard in a vertical (trimmed completely down) position. Why? Outboards are designed to be self-draining. Keeping the engine vertical allows all residual cooling water to drain out naturally through the exhaust hub and weep holes.

Important Warning: If you store the engine in a tilted-up position, rainwater or leftover cooling water can become trapped inside the gearcase passages or exhaust hub. When the temperature drops below freezing, this trapped water turns to ice, expanding and causing catastrophic, non-warrantable structural damage to your motor.

Need Expert Advice?

Winterizing is straightforward, but doing it right is essential for your motor’s longevity. If you need maintenance parts, specific guidance for your Yamabisi model, or are looking to upgrade your setup for the next season, our team is here to help.

Contact Yamabisi Outboard today for professional support and premium marine power solutions.

Share With

Latest Articles

Ink & Toner Finder

Brand
Series
Model
Get Quote